Ton

Green earthenware clay. Its green colour in oxidising atmosphere is a highlight in the range of low firing colours. Its fineness and plasticity make it an excellent choice for wheel- throwing and modelling. Very good behaviour with standard pottery glazes. Available in extruded body (moist form). Firing range*: 1050-1080ºC / Cone 05-04 Water content (throwing): 19% Plasticity (IP Atterberg): 15 Carbonate content (CaCO3): 16% Drying shrinkage: 5.1% Firing shrinkage 1050ºC: -0.1% Porosity (water absorption) 1050ºC: 12.8% Dry bending strength: 4.3 N/mm2 Fired bending strength 1050ºC: 36.1 N/mm2 Thermal coefficient 1050ºC (25-500ºC): 72.2x10^-7ºC^-1 (*) Firing range recommended for the clay to develop its best performance, both in terms of technical and safety characteristics, under conventional firing conditions. The colour samples may show temperatures outside the recommended range to provide a broader view, but these are pieces fired under controlled conditions. Cone equivalence according to Orton table for self-supporting cones, regular-SSB and 150ºC/hr heating rate.

White stoneware clay with 40% impalpable grog 0-0.2 mm (up to 80 Mesh). Formulated for artistic ceramics, it is ideal for throwing and modelling smooth pieces with fine details. The high content of grog confers an excellent behaviour during drying and firing. Its particular ivory colour after firing is much appreciated and provides an excellent ware for glazes and colouring oxides, which develop bright and intense tones. Suitable for tableware (food-safe), according to ISO 6486. Available in extruded body (moist form). Firing range*: 1240-1300ºC / Cone 6-10 Biscuit temperature: 1000ºC / Cone 06 Water content: 19% Plasticity (IP Atterberg): 16 Carbonate content (CaCO3): 0% Drying shrinkage: 5.9% Firing shrinkage 1300ºC: 7.0% Porosity (water absorption) at 1300ºC: 0.0% Dry bending strength: 3.0 N/mm2 Fired bending strength 1300ºC: 51.0 N/mm2 Thermal coefficient 1250ºC (25-500ºC): 60.4x10^-7ºC^-1 Available in the United States and Canada. ACMI AP Seal. Conforms to ASTM D-4236. (*) Firing range recommended for the clay to develop its best performance, both in terms of technical and safety characteristics, under conventional firing conditions. The colour samples may show temperatures outside the recommended range to provide a broader view, but these are pieces fired under controlled conditions. Cone equivalence according to Orton table for self-supporting cones, regular-SSB and 150ºC/hr heating rate.

Grey sculpture clay with 40% fine grog 0-0.5 mm (up to 35 Mesh). Formulated for artistic and decorative ceramics, it is ideal for sculpture and pieces for outdoors (garden pots, tiles, etc.). The high content of grog confers a beautiful textured surface and an excellent behaviour during drying and firing. Depending on the firing temperature, it develops an interesting range of greys, from cement to dark grey, which satisfies the most avant-garde trends in artistic and decorative ceramics. Available in extruded body (moist form). Firing range*: 1200-1300ºC / Cone 5-10 Biscuit temperature: 1000ºC / Cone 06 Water content: 17% Plasticity (IP Atterberg): 16 Carbonate content (CaCO3): 0% Drying shrinkage: 5.3% Firing shrinkage 1300ºC: 4.3% Porosity (water absorption) at 1300ºC: 4.5% Dry bending strength: 2.8 N/mm2 Fired bending strength (1300ºC): 37.8 N/mm2 Thermal coefficient 1250ºC (25-500ºC): 61.6x10^-7ºC^-1 Available in the United States and Canada. ACMI AP Seal. Conforms to ASTM D-4236 (*) Firing range recommended for the clay to develop its best performance, both in terms of technical and safety characteristics, under conventional firing conditions. The colour samples may show temperatures outside the recommended range to provide a broader view, but these are pieces fired under controlled conditions. Cone equivalence according to Orton table for self-supporting cones, regular-SSB and 150ºC/hr heating rate.

creme/Spots / cream speckled / crème moucheté

schamottierte Steinzeugmasse, geeignet für plast. Formgebungsmethoden, Brennfarbe: weiß-, rot-, schwarz-marmoriert

Steinzeugmasse, zum Drehen u. Modellieren geeignet. Gute Temperaturwechselbeständigkeit, f. Auflaufformen gut geeignet; besonders für Raku-Brand geeignet! 30% Molochite-Schamotte 0-0,5mm

Besonders hell wegen der enthaltenen Molochite

schamottierte Steinzeugmasse für plastische Formgebungsmethoden, Brennfarbe: rot-dunkelrot

unempfindlicher Ton für alle Zwecke, spez. Große Teile

ähnlich dem 9C, dänischen Ton

ähnlich dem 9C, dänischen Ton

bestellbar ab 1To